TTi TG120 - Generátor funkcií 20MHz

TG120 - 20MHz Dial-Set Function Generator

20MHz dial set function generator
0.2Hz to 20MHz frequency range
Sine, square and triangle waveforms plus dc
10mV to 20V pk-pk from 50 Ohms
DC offset control with zero detent
Variable symmetry control
External sweep input
Very low cost.

Detaily
Špecifikácie

20MHz from a low-cost generator
Most lower cost function generators use a technology which enables them to operate up to no more than 2MHz.
The TG120 utilises an alternative technology which retains its waveform quality right up to 20MHz.

Sweep mode operation (external)
The TG120 can be operated in sweep mode by connecting an external sweep voltage. A sweep range of at least 20:1 can be achieved.

Variable symmetry for pulse and ramp waveforms
The TG120 provides switchable bi-directional variable symmetry which enables variable duty cycle pulse waveforms and sawtooths to be generated.

Wide range level control
The TG120 provides a main output with a maximum emf of 20V pk-pk from a 50W source.

An amplitude vernier with a range of 26dB is combined with two -20dB switched attenuators to provide levels down to 10mV pk-pk. Variable DC offset of ą10V is available via a centre detent control.

Auxilliary Output
An auxilliary output provides a fixed 0 to +5V level suitable for driving both TTL and CMOS loads.

Frequency
Frequency Range:	0.2Hz to 20MHz in 8 overlapping decade ranges with fine adjustment by a vernier.
Vernier Range:	>10:1 on each range.
Vernier Accuracy:	Typically ± 5% of full scale.
Sweep Mode External
Input Impedance:	82 kW
Sweep Range:	Typically > 20:1
Input Sensitivity:	Typically 0 to 2V for 10:1 sweep
Max. Input Voltage:	±10V
Max. Slew Rate of sweep voltage:	0.1V/us
Operating Modes
(Specifications apply for the top decade of each frequency range and output 10V peak-to-peak into 50W termination).
Sine
Distortion:	Typically 2% on 200, 2k and 20k ranges.
Amplitude Flatness:	± 0.2dB to 200kHz; ± 2dB to 20MHz.
Triangle
Linearity:	Typically 99% on kHz ranges.
Squarewave
Rise and Fall Times:	<22ns
DC Range:	±10V from 50 Ω
Symettry
Symmetry Range:	Typically variable from 1:6 to 6:1 up to 500kHz.
Outputs
50 Ω
Three switch-selectable ranges with 26dB vernier control within each range.
0dB Range:	1V to 20V peak-to-peak (0.5V to 10V into 50W)
-20dB Range:	100mV to 2V peak-to-peak (50mV to 1V into 50W)
-40dB Range:	10mV to 0.2V peak-to-peak (5mV to 0.1V into 50W)
DC Offset Range:	±10V from 50 W. DC offset plus signal peak limited to ±10V (±5V into 50W). DC offset plus waveform attenuated proportionally in -20dB and -40dB position.
TTL/CMOS
Capable of driving 4 standard TTL loads.
General
Power:	230V or 115V nominal 50/60Hz, adjustable internally; operating range ą14% of nominal; 30VA max. Installation Category II.
Operating Range:	+5°C to + 40°C, 20% to 80% RH.
Storage Range:	-10°C to +65°C
Environmental:	Indoor use at altitudes to 2000m, Pollution Degree 1.
Electrical Safety:	Complies with EN61010-1.
EMC:	Complies with EN55011 and EN50082-1.
Size:	220(W) x 82(H) x 230(D) mm, (10.3 x 3.4 x 9.2") excluding feet.
Weight:	1.5 Kg (3.3lb).