TTi PL330TP Laboratórny stabilizovaný zdroj 32V/3.1A (230W) s možnosťou ovládania cez PC
PL-P Series - Bus programmable dc bench power supplies |
![Doprava zadarmo pre každý nákup nad 80€ s DPH vytvorený cez náš eshop s doručením na Slovensko.](https://cdn.myshoptet.com/usr/www.elso.sk/user/banners/cart.png?65d4bf61)
![Široké možnosti platby na dobierku, kartou online alebo bankovým prevodom.](https://cdn.myshoptet.com/usr/www.elso.sk/user/banners/card.png?65d4c037)
![Tovar skladom odosielame v deň objednávky (do 13:00)](https://cdn.myshoptet.com/usr/www.elso.sk/user/banners/parcel.png?65d4c238)
![Záručný, pozáručný servis teplomerov, multimetrov a iného metrologického vybavenia.](https://cdn.myshoptet.com/usr/www.elso.sk/user/banners/repair.png?65d4c103)
OVERVIEW The Thurlby Thandar PL-P series offers a high performance fully programmable power supply system at low cost. |
High resolution control and readback |
Main Output(s): | |
Output Range: | 0 - 32 Volts at 0 - 3.1A. |
Voltage Setting: | 12 bit resolution (10mV steps) |
Current Setting: | 12 bit resolution (1mA steps) |
Setting Accuracy: | Voltage: ±(0.1% + 10mV) Current: ±(0.2% + 2mA) |
Output Mode: | Constant voltage or constant current modes with automatic cross-over. |
Output Switch: | Electronic by interface command (front panel output switches must be set to ON) |
Readback Resolution: | Voltage: 10mV over the entire range Current: 1mA over the entire range |
Readback Accuracy: | Voltage: ±(0.1% of reading + 1 digit) Current: ±(0.3% of reading + 1 digit) |
Current Meter | |
Damping: | Nominally 20ms switchable to 2 sec and back by remote commands |
Output Terminals: | 4mm terminals on 19mm (0.75") spacing. |
Output Impedance: | Constant Voltage: Typically <5mW at 1kHz. Constant Current: Typically 50kW. |
Output Protection: | Max. output voltage +20 volts forward; diode clamped for reverse, up to 3A reverse current. |
Load Regulation: | <0.01% of max. output for 90% load change |
Line Regulation: | <0.01% of max. output for 10% line change |
Remote Sense: | Eliminates up to 0.5V drop per lead. |
Ripple and Noise: | Typically <1mV rms |
Transient Response: | <20usec to <50mV for 90% load change |
Temp. Coefficient: | Typically <100ppm/°C |
Meter Type: | Dual 4 digit with 12.5mm LEDS, |
Reading rate 4 per second. | |
Logic Output - PL330TP | |
Voltage Range: | 4 to 6 Volts in 10mV steps |
Output Current: | 1 to 7 Amps in approximately 1A steps |
Setting Accuracy: | Voltage: ±(0.2% + 10mV) |
Output Switch: | Electronic by interface command (front panel output switch must be set to ON) |
Readback Resolution: | Current: 10mA |
Readback Accuracy: | Current: ±(0.5% of reading + 1 digit ) |
Output Protection: | Over-voltage protection operates above 7V. Diode clamped for reverse currents up to 3A. |
Load Regulation: | <0.01% of max. output for 90% load change |
Line Regulation: | <0.01% of max. output for 10% line change |
Remote Sense: | Eliminates up to 0.5V drop per lead. |
Ripple and Noise: | Typically <1mV rms |
Transient Response: | <20µsec to <50mV for 90% load change |
Temp. Coefficient: | Typically <100ppm/°C |
Meter Type: | 3 digit with 12.5mm LEDs. Reading rate 4/s |
Remote Control Interfaces | |
Both interfaces feature full control, readback and status reporting. | |
RS232: | Variable Baud rate (9600 maximum), 9 pin D-connector (female). Fully compatible with ARC (Addressable RS232 Chain) system. |
GPIB: | Conforming with IEEE-488.1 and IEEE-488.2 |
Address Selection: | By rear panel DIP switch. |
Remote/Local: | Selected by front panel switch. |
Remote Command Response Time: |
Interface:<15 ms (single command, input buffer empty). |
Output Voltage - Up: | Time constant typically 2ms, e.g. 10ms to settle <1% of a step change, 15ms to settle < 0.1%. |
Output Voltage - Down: | Time constant determined by the discharge of the power supply output capacitor (47uF). Typically <10ms to settle within 1% for a 10V step change at 50mA load current; typically <200ms to settle within 1% at zero load. |
Output Current: | Typically 50ms to settle <10mA for a 1A change. |
General | |
Power Requirements: | 110, 120, 220 or 240VAC 50/60Hz ±10% |
Operating Range: | 5°C to 40°C, 20% to 80% RH |
Storage Range: | -20°C to +60°C |
Size: | 170mm(H) x 300mm(D) x 207mm(W) - PL330P 350mm(W) - PL330DP, 425mm(W) - PL330TP. |
Weight: | 6.5kg (PL330P), 12.5kg (PL330DP), 16kg (PL330TP). |
Rack Mount Option: | 19 inch 4U mount for two PL330P or one PL330DP/TP. Anti-tamper cover for security. |
Electrical Safety: | Designed and manufactured to comply with IEC 348 and IEC1010-1. Full safety sockets available to special order. |
EMC: | Designed and manufactured to comply with EN50081–1 and EN50082–1. |
Buďte prvý, kto napíše príspevok k tejto položke.